Ecu Pinout | Toyota 4afe

A: Japanese domestic market (JDM) and European (EDM) ECUs used slightly different wire colors. For example, JDM 4A-FEs often use a Yellow/White wire for injector #1 instead of Red/White. Always use a multimeter to confirm continuity from the sensor to the ECU pin number—ignore the color.

Check NE+ (A24) and NE- (A25) while cranking. You need an oscilloscope or a multimeter set to AC volts. You should see ~0.5V AC. No voltage? Your distributor pickup coil is dead.

Drop a comment below (if applicable) or consult the factory Toyota Electrical Wiring Diagram (EWD) for your specific chassis code. toyota 4afe ecu pinout

However, when things go wrong—or when you plan a standalone ECU swap or engine conversion—the wiring becomes the biggest headache. The Engine Control Unit (ECU) is the brain, but without a proper , that brain is just a plastic box with two connectors.

| Pin | Wire Color | Signal Name | Function | | :--- | :--- | :--- | :--- | | | White | IGT | Ignition Timing Signal (from ECU to igniter) | | B02 | Red/White | #10 | Fuel Injector Cylinder #1 | | B03 | Blue | #20 | Fuel Injector Cylinder #2 | | B04 | Yellow | #30 | Fuel Injector Cylinder #3 | | B05 | Brown | #40 | Fuel Injector Cylinder #4 | | B06 | Black/Yellow | FC | Circuit Opening Relay (Fuel Pump Control) | | B07 | Light Green | VSV (CC) | Charcoal Canister Purge VSV | | B08 | - | - | Empty | | B09 | Red/White | +BM | Backup power for ECU memory (constant 12V) | | B10 | Black/Orange | W | Check Engine Light (MIL) Control | | B11 | Blue/White | ACT | Air Conditioning Switch Signal (to ECU) | | B12 | Red/Black | ACMG | A/C Compressor Magnetic Clutch Relay | | B13 | Black | E1 | Sensor Ground (shared with TPS, MAP, etc.) | | B14 | Black/White | E03 | Injector Power Ground | | B15 | Black/White | E04 | Injector Power Ground | | B16 | - | TE1 | Diagnostic Jumper Pin (for flashing CEL codes) | A: Japanese domestic market (JDM) and European (EDM)

A: The 7AFE (1.8L version) ECU has different fuel maps and ignition timing. It will run a 4AFE, but poorly—rich at idle and lean at high RPM. Pinouts are similar but not identical. Not recommended. Check NE+ (A24) and NE- (A25) while cranking

| Pin | Wire Color | Signal Name | Function | | :--- | :--- | :--- | :--- | | | Red | +B1 | Main EFI Relay Power Input | | A02 | Red | +B | Main EFI Relay Power Input | | A03 | Black/Yellow | IGSW | Ignition Switch ON Signal (12V) | | A04 | - | - | Empty | | A05 | Brown | VTA | Throttle Position Sensor (TPS) Signal | | A06 | Light Green | VCC | TPS Sensor 5V Reference | | A07 | Black | E2 | TPS Ground | | A08 | Blue/Red | PIM | MAP Sensor Signal (0-5V) | | A09 | Red/Blue | THW | Engine Coolant Temp (ECT) Signal | | A10 | White/Black | STA | Starter Signal (from ignition switch) | | A11 | Light Green/Black | VC | Common 5V Sensor Reference | | A12 | Green/Red | VAF (or MAP Sig) | Early models: AFM signal | | A13 | Yellow/Red | KNK | Knock Sensor Signal | | A14 | Red/White | SP1 | Vehicle Speed Sensor (VSS) Input | | A15 | Black/White | E01 | ECU Power Ground (to engine block) | | A16 | Black/White | E02 | ECU Power Ground (to engine block) | | A17 | - | - | Empty | | A18 | Yellow | OX1 | Front Heated Oxygen Sensor (O2) Signal | | A19 | Black/Red | VSV EGR | EGR Vacuum Switching Valve Control | | A20 | Brown/Yellow | ISC1 | Idle Speed Control Valve Coil 1 | | A21 | Brown | ISC2 | Idle Speed Control Valve Coil 2 | | A22 | Light Green/Red | G- | Distributor Pickup Coil (Negative) | | A23 | Light Green | G+ | Distributor Pickup Coil (Positive) | | A24 | Red | NE+ | Distributor RPM Signal (Positive) | | A25 | White | NE- | Distributor RPM Signal (Negative) | | A26 | White/Red | IGF | Ignition Confirmation Signal (to igniter) | Pro Tip: Pins A01 and A02 provide 12V. If your fuel pump doesn’t prime, check these wires first. Pins A15 and A16 are critical grounds—never assume chassis ground is enough. Connector B (16 pins) – Injectors & Ignition This connector handles high-current outputs.